LANMASTER, shielded, Category 6, RJ45 keystone jack, 180-degree, 45-degree
The module can be used to complete shielded telecommunication sockets installed in wall trunks, in a wall box, also for installation in modular patch panels (see the compatibility items).
Category 6 compliant.
The module has a standard Keystone form-factor and can be used not only in LANMASTER socket adapters, but also in socket adapters from other manufacturers.
There is a shielded eight-pin RJ-45 socket on the front side of the module, and there is a block for eight contacts of the IDC110 type on the back side, located at an angle of 180˚ to the front surface of the module.
The continuity of the screen is ensured by a cable clamp (in the form of a metal clasp) and a shielded cover.
The insulation displacement contact method is used (IDC) to terminate incoming cable.
There is a wiring diagram for the cable conductors between the IDC pins in accordance with the T568A and T568B wire map for ease of installation.
-1.png)
Most frequently asked questions and answers
What is the LAN-OK45S6/180 Keystone module used for?
The Keystone module with an RJ-45 socket (8P8C, eight-contact connector) is used for equipping shielded telecommunication outlets installed in a box, on a wall or in a wall, as well as in modular patch panels (see the compatibility table). The module has the standard Keystone size and suits products of other manufacturers of this format. It complies with the requirements of category 6. Features: the IDC110 contact block is at 180° to the front surface.
Which speed does the LAN-OK45S6/180 module support?
The module complies with category 6 and is intended for links for Gigabit Ethernet networks and, over a limited link length, 10GBASE-T. The link category is determined by its weakest component, so the cable, patch panels and cords must be of the same or a higher category.
How do I terminate a cable in the LAN-OK45S6/180 Keystone module?
Strip the cable sheath, arrange the conductors according to the diagram printed on the module (T568A or T568B; use one scheme along the whole link) and punch them down to the IDC (insulation displacement contact) contacts with a 110-type punch-down tool. The IDC contacts cut through the insulation, so the conductors need not be stripped. Fit the protective insert if it is included: it holds the conductors and protects them from being pulled out when the cable is tensioned. For a shielded module, connect the cable screen to the body: screen continuity is ensured by clamping the cover halves together.
How do I ground the LAN-OK45S6/180 shielded module?
The cable screen must be reliably connected to the module screen, and the module screen to a grounded patch panel or an outlet with a metal body. Use shielded cable and patch cords; a break in the screen at any point removes the link protection against interference. Grounding must be made at one point, without several paths with different potentials.
Which patch panels and outlets is the LAN-OK45S6/180 module compatible with?
The module is installed in Keystone-format modular patch panels and outlets. The compatibility of specific panels is given in the compatibility table on the product page; the module width corresponds to the standard Keystone size.
What should I do if a link with the LAN-OK45S6/180 module is unstable?
Check that the conductors are terminated by the same scheme (T568A or T568B) at both ends of the link, that there is no open or short circuit and that the pairs are not untwisted beyond the length required for termination. Check the link with a tester, redo the termination if necessary and make sure the category of all components is not lower than required.
Can LAN-OK45S6/180 still be ordered if it has been discontinued?
The product has been discontinued, but some quantity is still available for shipment: an order is possible only within the remaining stock at the warehouse of the manufacturer and distributors. For new projects choose current products of the same category.
Package dimensions and weight
Single item
| Unit | length × width × height (mm) | Weight (kg) | Volume (m3) |
|---|---|---|---|
| pcs | 180 × 110 × 10 | 0.015 | 0.000198 |