Structured cabling installer toolkit

Structured cabling installer toolkit LAN-NT-TK/INST: specifications, description and use in structured cabling and LANMASTER infrastructure projects.
LAN-NT-TK/INST

The tool kit is intended for installation of twisted pair cable on patch panels, sockets, and cross-connect blocks. The tools included in the kit allow you to make of cable cutting and stripping, cable termination on IDC-connectors, and crimping RJ-12 and RJ-45 plugs. The tools are supplied in a plastic case with compartments for easy storage and carrying.

The kit includes:

  • RJ-12 and RJ-45 plug crimping tool, side crimp hole,
  • Cable jacket striping tool,
  • 110 Punch-down tool for interchangeable termination blades,
  • Electric soldering iron 30W/220V,
  • Twisted pair cable connection tester (without batteries),
  • RJ-45 8P8C 5e cat. plug – 8 pieces,
  • Tape meter, 2 m,
  • Flathead screwdriver (180 mm length),
  • Flathead screwdriver (150 mm length),
  • Phillips screwdriver (180 mm length),
  • Phillips screwdriver (150 mm length),
  • Utility knife,
  • Narrow pliers,
  • Side cutters,
  • Tweezers,
  • Cable striping tool with IDC punch-down blade.

Frequently asked questions and answers

What work is the LAN-NT-TK/INST designed for?

The kit is intended for installing twisted-pair cable on patch panels, telecom outlets and cross-connects, and for making jumper cords. It includes tools for cable stripping and cutting, IDC termination, and RJ-12/RJ-45 crimping.

What is included in the kit?

The current product page lists an RJ-12/RJ-45 crimper, a cable stripper, a 110-type impact tool with interchangeable blades, a wire-map tester without batteries, a 30 W / 220 V soldering iron, eight Cat 5e RJ-45 plugs and hand tools. Confirm the current order configuration when purchasing.

LAN-NT-TK/INST tool kit
LAN-NT-TK/INST kit contents
Can I terminate cable on patch panels and outlets with this kit?

Yes. The kit includes a 110-type impact tool and a separate tool for cable stripping and seating conductors in IDC contacts. Select the blade and termination method for the installed IDC module; not all blocks and modules are interchangeable.

Does the tester certify the cable category or data rate?

The tester checks the wiring and termination of twisted-pair cable, known as its wire map. A twisted-pair wire-map test can help identify opens, shorts and conductor wiring errors, but the tester does not certify that the link meets any category's performance requirements or supports a specific data rate.

Why does the tester show a fault after crimping?

Check the conductor termination order at both ends, confirm that each conductor reaches its contact, and look for nicks in the conductor insulation made while stripping the cable jacket. Verify plug-to-cable compatibility and that the plug captures the cable jacket. If uncertain, cut off the terminated section and redo it.

Are batteries needed for the tester?

Yes. The tester is supplied without batteries. Check the tester's own instructions for its battery type and prepare the batteries separately.

Can this kit be used on coaxial cable?

No, the kit is designed for twisted-pair cable and RJ-11/RJ-12/RJ-45 plugs. For coaxial cable, use a dedicated kit such as LAN-NT-TK/COAX.

Didn’t find an answer to your question?

Package dimensions and weight

Single item

Unit length × width × height (mm) Weight (kg) Volume (m3)
pcs 330 × 70 × 270 1.777 0.006237

Package

Unit length × width × height (mm) Weight (kg) Volume (m3)
box 560 × 340 × 350 17 0.06664

Product Codes (1)

Specifications are subject to change without notice. For the most current information, consult LANMASTER or an authorized LANMASTER partner/distributor.