LANMASTER, shielded, Category 6A, RJ45 keystone jack, 180-degree, 45-degree

LANMASTER, shielded, Category 6A, RJ45 keystone jack, 180-degree, 45-degree for copper structured cabling systems. LANMASTER product information, specifications and part number details.
Discontinued
LAN-OK45S6A/180


Most frequently asked questions and answers

What is the LAN-OK45S6A/180 Keystone module used for?

The Keystone module with an RJ-45 socket (8P8C, eight-contact connector) is used for equipping shielded telecommunication outlets installed in a box, on a wall or in a wall, as well as in modular patch panels (see the compatibility table). The module has the standard Keystone size and suits products of other manufacturers of this format. It complies with the requirements of category 6A. Features: the IDC110 contact block is at 180° to the front surface.

LANMASTER, shielded, Category 6A, RJ45 keystone jack, 180-degree, 45-degree LAN-OK45S6A/180
Appearance LAN-OK45S6A/180
Which speed does the LAN-OK45S6A/180 module support?

The module complies with category 6A and is intended for links for 10GBASE-T networks over links up to 100 m. The link category is determined by its weakest component, so the cable, patch panels and cords must be of the same or a higher category.

How do I terminate a cable in the LAN-OK45S6A/180 Keystone module?

Strip the cable sheath, arrange the conductors according to the diagram printed on the module (T568A or T568B; use one scheme along the whole link) and punch them down to the IDC (insulation displacement contact) contacts with a 110-type punch-down tool. The IDC contacts cut through the insulation, so the conductors need not be stripped. Fit the protective insert if it is included: it holds the conductors and protects them from being pulled out when the cable is tensioned. For a shielded module, connect the cable screen to the body: screen continuity is ensured by clamping the cover halves together.

How do I ground the LAN-OK45S6A/180 shielded module?

The cable screen must be reliably connected to the module screen, and the module screen to a grounded patch panel or an outlet with a metal body. Use shielded cable and patch cords; a break in the screen at any point removes the link protection against interference. Grounding must be made at one point, without several paths with different potentials.

Which patch panels and outlets is the LAN-OK45S6A/180 module compatible with?

The module is installed in Keystone-format modular patch panels and outlets. The compatibility of specific panels is given in the compatibility table on the product page; the module width corresponds to the standard Keystone size.

What should I do if a link with the LAN-OK45S6A/180 module is unstable?

Check that the conductors are terminated by the same scheme (T568A or T568B) at both ends of the link, that there is no open or short circuit and that the pairs are not untwisted beyond the length required for termination. Check the link with a tester, redo the termination if necessary and make sure the category of all components is not lower than required.

What replaces LAN-OK45S6A/180 if it has been discontinued?

The LAN-TK45S6A/180R model is provided as a replacement: follow the link and compare its characteristics with the former item. The remaining stock of LAN-OK45S6A/180 is limited to the quantity left at the warehouse of the manufacturer and distributors.

Didn’t find an answer to your question?

Package dimensions and weight

Single item

Unit length × width × height (mm) Weight (kg) Volume (m3)
pcs 35 × 15 × 25 0.03 0.000013

Product Codes (1)

  • LANMASTER, shielded, Category 6A, RJ45 keystone jack, 180-degree, 45-degree
Specifications are subject to change without notice. For the most current information, consult LANMASTER or an authorized LANMASTER partner/distributor.