TWT, U/UTP, Category 5e, twisted-pair cable, 25-pair, unshielded, 305 m
TWT, U/UTP, Category 5e, twisted-pair cable, 25-pair, unshielded, 305 m. Product for LANMASTER copper structured cabling systems. Use in twt multipair cables applications according to the project design and product specifications.
Most frequently asked questions and answers
What is the TWT-5EUTP25-OUT cable used for?
TWT-5EUTP25-OUT is a unshielded category 5e cable made of 25 pairs of solid copper conductors. The multi-pair cable is used for backbone links between cross-connects and floor cabinets, telephone and low-voltage backbones and for connecting telephone exchange ports to cross-connect equipment. For connecting a work area over Ethernet use a four-pair cable. The conductor size is 24 AWG.
What is the TWT-5EUTP25-OUT cable made of and what are its features?
Each conductor is insulated with high-density polyethylene (HDPE); two conductors are twisted into a pair, and all pairs are enclosed in a common sheath. The cable has an outdoor polyethylene (PE) sheath. The construction also includes: a ripcord for stripping the sheath.
Can the TWT-5EUTP25-OUT cable be installed outdoors and inside a building?
The cable is intended for outdoor installation: the polyethylene sheath protects the conductors from external influences and sunlight. Inside a building, route only the entry section and connect the cable to a cross-connect or an outlet; for indoor installation use a cable with a PVC (polyvinyl chloride) or LSZH (low smoke zero halogen) sheath that meets the fire-safety requirements of the site. When installing in the ground, place the cable in a protective duct.
How do I terminate the TWT-5EUTP25-OUT cable in an outlet or patch panel?
Strip the outer sheath over the minimum length without damaging the conductor insulation. Untwist the pairs only as far as needed for termination and arrange the conductors according to the colour scheme on the module or panel (T568B or T568A, identical along the whole link). Punch the conductors down with a punch-down tool for 110 or Krone contacts and trim the excess. Do not terminate with a screwdriver: it damages the contacts and the insulation.
How do I identify the pair numbers in the TWT-5EUTP25-OUT multi-pair cable?
Pairs are numbered according to the standard colour code: the primary colour defines a group of five pairs (white, red, black, yellow, violet) and the secondary colour defines the pair within the group (blue, orange, green, brown, slate). For example, pair 1 is white/blue, pair 6 is red/blue, pair 13 is black/green. Ring out and label the pairs before termination.
How do I terminate the TWT-5EUTP25-OUT multi-pair cable on a cross-connect or patch panel?
Strip the sheath to the required length, separate the bundles and pairs by the colour code and route them to 110-type blocks or Krone/LSA strips in numbering order. For a high-count cable, fix it to a bracket or with a clamp so that its weight is not transferred to the contacts. Punch down the pairs while keeping the twist up to the termination point and label the blocks. For switching telephone lines, use a telephone patch panel with a multi-pair input.
Can the TWT-5EUTP25-OUT multi-pair cable be used for Ethernet?
To connect work areas and network equipment over Ethernet, use a four-pair cable of the appropriate category. The multi-pair cable is intended for backbone and telephone links, where one pair serves one channel. If data is nevertheless transmitted over it, use different bundles for different systems and check the link with a tester.
How do I install the TWT-5EUTP25-OUT cable correctly?
Unwind the cable without loops or kinks and do not exceed the permitted pulling force. Observe the minimum bend radius and do not tighten cable ties so that the sheath is crushed. Do not run the cable close to and in parallel with power lines; cross them at an angle close to 90°. Leave a service loop at the outlet and in the cabinet.
How do I unwind the TWT-5EUTP25-OUT cable from its package and how do I store it?
Place the reel on a rotating support and unwind the cable by turning the reel instead of pulling the turns off the side. Store the cable in a dry room in its factory packaging and protect the cable ends from moisture and contamination.
Package dimensions and weight
Single item
| Unit | length × width × height (mm) | Weight (kg) | Volume (m3) |
|---|---|---|---|
| reel | 530 × 360 × 530 | 51.2 | 0.101124 |